Can I Install A Bath Tub Myself?
Further DetailsWe have stumbled upon this post relating to A Step-by-Step Guide to Installing a Bathtub directly below on the internet and felt it made perfect sense to talk about it with you on this page.
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably tough job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open up a wall to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and set in the brand-new one. Make sure you have actually qualified on your own for the work as well as fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your washroom if you have currently bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices as well as product checklist ought to consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Using the two wood boards under its feet, put the tub in the required placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water and also examine all joints and also new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow outlet and also the typical outlet for leakages.
Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Preparing for the Setup
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that article post was a smart idea. Appreciated our blog posting? Please share it. Let others locate it. Many thanks for your time. Don't hesitate to pay a visit to our website back soon.
Request An Appointment